As local governments and municipalities are working to resolve the issue of fats, oils and grease (FOG) that are clogging sewers systems, the issue has an immediate impact not just on households and restaurants, but also for the industrial sector such as remanufacturing and metal finishing.
Any manufacturer that discharges wastewater into municipal sewers systems is facing stricter FOG regulations...
Read More
Written by Mike Valenti, Director of Technology
Hubbard-Hall has developed an emulsifying cleaner that is optimized for filtration. In conjunction with its membrane filter, the solution enables users to regenerate cleaning solution.
Parts cleaning systems work by transferring soil into the cleaning solution. Those solutions have a finite capacity so they must be replaced periodically. That process...
Read More
In the push to ensure greater environmental controls over manufacturing operations, government regulations continue to tighten. One study found that the U.S. Environmental Protection Agency (EPA) has imposed 972 regulations on manufacturers in just the past 30 years alone. That same study found that violations have cost companies more than a billion in fines, and cost individuals their freedom –...
Read More
Biological wastewater treatment can be a more effective solution for managing wastewater in the industrial world.
But what are biologics? Instead of conventionally removing pollutants, a biological system uses bacteria substances upon their contact with the waste stream. By harnessing this power for nature, metal finishing manufacturers can remove key compounds such as: BOD/COD, macronutrients lik...
Read More
A lot of different markets use membrane filtration – medical devices, pharma, optical, wastewater, oil and gas, food, and of course manufacturing. They use membrane filtration to pick what element they need to filter out from the reaction and keep the other elements working in the process.
In surface treatment, it’s very common to use filtration on the paint line when you are doing an e-...
Read More
In many facilities, the maintenance department oversees the wastewater system. However, when a plant has a dedicated wastewater operator their whole job is ensuring that the wastewater leaving the facility meets all permitted discharge requirements. A Wastewater Operator is also known as a Water Quality Protector.
A wastewater operator should receive training for more than just wastewater treatm...
Read More
A manufacturer reached out to us because they were growing and at risk of not meeting their discharge limits. They had worked with other chemical suppliers and were told that they might need to purchase an entirely new system, something that would cost the company up to $310,565.00. Their current system, a very basic system without a lot of computer technology, was outdated. It did not have a ...
Read More
The longevity and durability of any painted application can be difficult to determine given the abbreviated timeframe of development and manufacturing cycles. Yet, it is incumbent on manufacturers to produce coatings that exhibit resilience to time, wear, and environment factors. As such, industry has devised several methods and standards for the evaluation of painted coatings and their associated...
Read More
The Metal Guard product line has been around 20 plus years now and has different variations to meet varying needs. Here are a few questions that should be answered to determine which Metal Guard our experts would recommend.
Is the rust preventative being applied to the part during an in-process step or is this the final step in the production process?
Will the part be stored indoors or outdoors...
Read More
Whether you are using solvent or aqueous cleaner, you need to consider many variables to find the best process to properly clean your parts before heat treatment, to extend the life of your equipment and to supply high-quality heat treatment without any soft spots or stains on the part.
1. What is the contamination? What kind of oil are you using that will need to be removed?
Do a deep dive into ...
Read More
In recent times, the industrial sector has faced a significant challenge due to the abrupt halt in the production of trichloroethylene (TCE), a versatile solvent widely employed in industrial cleaning and degreasing processes. This unforeseen disruption has compelled businesses to rethink their approach to solvent management and explore innovative solutions to address the scarcity.
Trichloroethyle...
Read More
Cleaning processes play a crucial role in various industries, ensuring the removal of contaminants to maintain optimal performance and longevity of components. This blog takes a closer look at the intricacies of different cleaning processes, shedding light on the essential characteristics that applicators need to consider. Let’s explore the factors that matter most when selecting the right c...
Read More
One of the biggest wastes in a phosphating application is the productivity loss due to rejects & reworks. As with most multi-step chemical processes, having a clean contaminate-free surface is key to achieving a proper phosphate coating. This enables the reaction to proceed across the entire working surface area and ensures that the substrate is activated and free of problematic soils.
Organic...
Read More
In the process of aluminum cleaning, managing zincate drag-in and avoiding blistering issues is important for ensuring quality. A customer case study reveals a solution that balances quality maintenance and cost-effectiveness, highlighting the importance of improving treatment processes.
When a manufacturing customer consistently faced blistering concerns around the third metal turnover (MTO). The...
Read More
Identify the Root Cause
One of the biggest challenges operators face is knowing whether a part is clean enough . Many issues can be traced back to inadequate cleaning and pretreatment of parts. Variables are changing upstream that are out of your control, which causes downstream issues. While problems can sometimes arise due to bath issues, a significant portion correlates with ineffective pretrea...
Read More
To the uninitiated, the daily operation of a phosphate bath can appear daunting – perhaps even a bit convoluted. While temperature and concentration are common parameters for most chemical applications, both phosphate baths have added complexity acid points, acid ratios, dissolved iron, sludging, heating source, & more. In this post, we will highlight some of the key features of these proces...
Read More
Concrete Corrosion. Mention corrosion and most people think rusting metal. True, but reinforced concrete also corrodes and deteriorates. How so?
Reinforced concrete is the backbone of every wastewater collection system. Alkaline materials in the cement phase of concrete are extremely susceptible to corrosion.
Hydrogen sulfide (H2S) is the root contributor to corrosion in sewer systems. H2S is a by...
Read More
Do you know the chorus of this children’s song?
“But the cat came back the very next day,
The cat came back, we thought he was a goner
But the cat came back; it just couldn’t stay away.
Away, away, yea, yea, yea…”
Like the kitty that kept coming back, thick foam on your aeration basin and digester keeps coming back no matter what you try. Why is that? And what can you do to finally get r...
Read More
Microscopic examination of mixed liquor can be a significant aid in the evaluation of the activated sludge process. The presence of various microorganisms within the sludge floc can rapidly indicate good or poor treatment. One of the operator’s primary jobs is to provide a favorable environment to support bug life. Knowing when and how to use a microscope is one of the most important tools in an...
Read More
Manganese and zinc phosphate coatings have been utilized as established solutions for over a century, delivering proven benefits in a number of applications. Beyond their mechanical benefits and anti-corrosion properties, these coatings create an optimal surface for paint adhesion by increasing the substrate’s total surface area with the crystalline coating that is formed. However, for applicati...
Read More
One of the more frustrating aspects of being a paint applicator is having to deal with the buildup of paint on your racks and fixtures. These custom components are a considerable investment for many applicators and ensuring that they remain functional and lasting is critical to managing a process’s operation cost. Several different methods are used to maintain these components including burn-off...
Read More
Question: Can I “overwhelm” my wastewater system?
Answer:
Yes. When wastewater systems are overwhelmed, a pass-through event occurs. If more wastewater goes into the system than the system was designed to handle, the system is not going to be able to remove all the contaminants. The contaminants are going to go out the door. So, when introducing new processes in manufacturing, always conside...
Read More
Traditionally, paint stripping was conducted with methylene chloride or DCM, which is an excellent solvent that was prevalent across many industrial applications. As manufacturers began to learn more about the chemical’s toxicity and carcinogenicity, it quickly ran out of favor as safer alternative methods emerged. Organic paint strippers today are much safer and user-friendly. These products ha...
Read More
Bench testing is not an exact science. Each test can produce slightly different results because every wastewater sample is slightly different. By using bench tests to help determine the best chemicals for the wastewater system, you can eliminate weeks of trial and error on a large scale. You will still need to adjust the wastewater system while the water flows to dial in chemical feeds, but bench ...
Read More
Number 1: Before you put the bath in, passivate the tank and all the plumbing. Passivation is when you’re dissolving the nickel with a nitric acid, using a stainless tank in which you’re putting a passive film which stops it from plating out. A good nitric will stop it from plating out immediately. I’ve seen it happen many times. I’ll get the call and say, “Hey, I put...
Read More
What does Earth Day mean to you? For the metal finishing industry, it means that we continue to make the many parts that make the world go round, from airplane and automobiles to medical devices. If it is metal, we touch it. A side aspect of our industry is that we use millions of gallons of water a year to make these parts. This is water we pull from our communities. In the United States it is es...
Read More
In a recent conversation with Barbara & Ed Kanegsberg (The Cleaning Lady and The Rocket Scientist), we discussed the United States Environmental Protection Agency’s (EPA) Toxic Substance Control Act (TSCA). Congress has asked the EPA to look at existing chemicals and evaluate their risk. They look at them chemical by chemical, step by step.
The risk evaluation is to determine if there ...
Read More
Myth 1 of 8: Water is Obviously “Cheaper” than Solvents.
Regular city water alone won’t clean anything. It needs surfactants and detergents that lower surface tension and remove soils. These are consumed during cleaning and need replenishing. Higher temperatures are needed to activate cleaning chemistry, which is important for ensuring good wetting and evaporation after rinsing, but that con...
Read More
Hubbard-Hall continues to expand the chemical management and distribution services for semiconductor customers by supplying high purity commodity chemistries and representing strategic suppliers with specialty technologies and products. Particularly over the last couple of years, managing the distribution, warehousing of these materials to ensure that no one is shutting down their lines. Fabricati...
Read More
‘I have used TCE for years. Never had a problem. Now it’s a problem!’
Let’s face it, you are in the business of producing metal parts, not dealing with chemistry. If the solvent isn’t cleaning effectively, you simply add more. You probably test for acid acceptance, but not frequently. So why isn’t that enough now?
Older open top degreasers used a lot of solvent through emissive losses ...
Read More
Which is Better, Solvent or Aqueous Cleaning?
The answer? It depends! Surface cleaning of metal components is dependent on numerous factors.
The type and composition of the contaminant
The complexity of the part to be cleaned
The type of metal
How clean is clean?
Available footprint within the shop operation
Parts throughput
Energy costs
Waste treatment availability (in house or haul off)
At a h...
Read More
How does TCE go acid?
Some common conditions that can cause the TCE to go acid are;
Excess water from condensation
Wet parts
Damaged cooling coils
Chlorinated oils
Water-based cutting fluids
Always check with the manufacturer of the vapor degreasing equipment or the supplier of the solvent for guidance.
How do I know if my TCE has gone acid?
An acid acceptance test is the most accurate way to de...
Read More
When considering proper pre and post cleaning of parts, quality is just one consideration for captive heat treaters and commercial shops. The other is the damage that both vacuum and atmospheric furnaces can incur, leaving shops with costly problems to their equipment including: loss of vacuum, contamination to future runs, smoke bombs and shortened quench oil life.
Vacuum Furnaces
3 major manufac...
Read More
So when we look at manufacturing industries across the board, a lot of people plan for expansion and production, such as adding new lines increasing production hours, and that puts an extra strain on their wastewater systems. We want to future-proof our wastewater systems so that when we do those manufacturing increases, we don’t have to worry later down the line about if our wastewater syst...
Read More
The most common type of corrosion – called atmospheric corrosion – occurs when a metal surface is exposed to oxygen and moisture which then causes a chemical reaction producing iron oxide or rust. For a metal finisher rust is a problem with real consequences. Here we are talking to Larry Ensley, Director of Technical Applications and sharing ideas on how to address it.
Click to Downloa...
Read More
A conversation with Hubbard-Hall’s Robin Deal
Robin is a Field Service Engineer specializing in industrial wastewater treatment for 7 years. She spends much of her time in the field educating customers while helping them meet their wastewater permit requirements. When in the lab Robin is working toward finding efficient ways for customers to transform their wastewater treatment processes to ...
Read More
I work with many metal finishers that clean the “soft” metals, specifically aluminum and copper alloys. One common, and more recurring issue I see, is staining of these alloys after the forming lubricants are removed in a cleaning step. In the push to go green, many fabricators are switching to water emulsifiable metal working fluids. The formulators of these lubes use different addi...
Read More
I present to industry on a regular basis, about the importance of “Process over Product” when it comes to getting clean parts in your metal finishing operation. This was reinforced to me more than ever, during an onsite cleaning trial at a new customer this week.
In this particular case we are cleaning a critical aluminum part, and a improved cleaner was needed. But it is only part of ...
Read More
A conversation with Hubbard-Hall’s Joshua McClellan
As a Hubbard-Hall application engineer, Joshua works closely with customers to understand their specific operations and applications of cleaning chemistry to get better results with less chemistry. He has worked with multiple chemical businesses over his career, specializing in chemical application technologies.
Download PDF
What are the p...
Read More
The heart of industry, almost nothing can be manufactured without heat-treating. We recently caught up with Bob Farrell (Senior Vice President and Technical Director at Hubbard-Hall) and asked him a few questions about the heat-treat market, what he has seen in his 30 years of experience and what lies ahead for manufactures using these applications.
Read More: Download the interview PDF
Why are m...
Read More
Black oxide is the conversion of a base metal material to an oxide of that base metal material. A prime example would be Fe3O4, which is black iron oxide, otherwise known as magnetite; another is a CuO, or copper monoxide. It occurs when the chemicals react with a base material to form an oxide of the base’s primary constituent. In the case of stainless steel, not only does it form oxides, but i...
Read More
A conversation with Hubbard Hall’s Jerry Dwyer
Jerry Dwyer CEF, is Hubbard Hall’s market manager for product groups pertaining to heat treating, black oxide and phosphates. His background and experience have established him with knowledgeable insight into the world of heat treating and metal finishing. Dwyer specializes in the above processes and has over a thirty-year history in the heat trea...
Read More
Surveys show that only 25% of all metal finishing operations in North America offer electropolishing to their customers. With a possible rise in the need for electropolishing thanks to reshoring efforts for medical parts and equipment, demand could outpace availability as manufacturers seek to find finishers to electropolish those parts to a high specificity.
Fortunately, electropolishing lines ar...
Read More
Tackling Hazy Water Hassles With Absolute Clarity
When it comes to cloudy wastewater, there are any number of reasons you can find yourself in a fog. From residual emulsified oil and surfactants to overdosing on polymers and coagulants, Hubbard-Hall’s wastewater treatment technical team can help you diagnose and treat the problem. What are some of the reasons for the cloudy wastewater?
Resi...
Read More
Recently, a leading manufacturer of high-value parts for the aerospace industry ran into a cleaning challenge – namely, the cleanliness of parts going through its vacuum brazing process. The existing process was falling short – and experiencing a high field failure rate. Compounding the challenge was a large variation of aluminum alloys and forming processes of the parts.
The customer engaged ...
Read More
A quick list of the most important factors to bear in mind when determining your rinsing process.
Water is becoming an increasingly expensive commodity with even further restrictions in certain areas of the country (pity the poor folks in California). As a result, there has never been a better time to give some thought to maximizing the efficiency of your rinsing process. Put simply, rinsing is a ...
Read More
